• Lv0
    粉丝0

积分0 / 贡献0

提问3答案被采纳0文章0

OH4.0 rk3568 系统启动后无法输入命令

Juniar 显示全部楼层 发表于 2024-7-25 11:10:15

In ddrconfig:7 LPDDR4X, 324MHz BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB tdqss: cs0 dqs0: -72ps, dqs1: -144ps, dqs2: -120ps, dqs3: -241ps, tdqss: cs1 dqs0: -72ps, dqs1: -144ps, dqs2: -120ps, dqs3: -217ps,

change to: 324MHz PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:41% dram drv:40,odt:0 clk skew:0x66

change to: 528MHz PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:41% dram drv:40,odt:0 clk skew:0x58

change to: 780MHz PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:41% dram drv:40,odt:0 clk skew:0x58

change to: 1560MHz(final freq) PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:22% dram drv:40,odt:80 vref_ca:00000071 clk skew:0x3f cs 0: the read training result: DQS0:0x35, DQS1:0x31, DQS2:0x3a, DQS3:0x2e, min :0x13 0x13 0x15 0x12 0x3 0x6 0x7 0x2 , 0xc 0xc 0x2 0x4 0xb 0x6 0x7 0x4 , 0x17 0x1a 0x13 0x13 0x7 0x2 0x5 0x7 , 0xe 0xb 0x7 0x2 0xd 0xc 0xa 0xa , mid :0x30 0x2f 0x31 0x2d 0x1e 0x22 0x23 0x1e ,0x28 0x25 0x1d 0x1e 0x27 0x21 0x23 0x1f , 0x33 0x34 0x2e 0x2c 0x23 0x1d 0x1f 0x21 ,0x2a 0x25 0x23 0x1d 0x29 0x27 0x24 0x26 , max :0x4d 0x4c 0x4d 0x49 0x3a 0x3e 0x3f 0x3b ,0x44 0x3f 0x38 0x39 0x44 0x3c 0x3f 0x3b , 0x4f 0x4f 0x49 0x45 0x3f 0x39 0x3a 0x3c ,0x47 0x40 0x3f 0x38 0x45 0x43 0x3e 0x43 , range:0x3a 0x39 0x38 0x37 0x37 0x38 0x38 0x39 ,0x38 0x33 0x36 0x35 0x39 0x36 0x38 0x37 , 0x38 0x35 0x36 0x32 0x38 0x37 0x35 0x35 ,0x39 0x35 0x38 0x36 0x38 0x37 0x34 0x39 , the write training result: DQS0:0x31, DQS1:0x23, DQS2:0x28, DQS3:0xf, min :0x6e 0x73 0x73 0x72 0x63 0x67 0x68 0x69 0x65 ,0x5c 0x5a 0x52 0x54 0x5e 0x5b 0x5a 0x5b 0x54 , 0x69 0x69 0x62 0x62 0x56 0x55 0x52 0x59 0x57 ,0x4a 0x49 0x45 0x43 0x4c 0x4e 0x4d 0x4e 0x47 , mid :0x89 0x8c 0x8c 0x8c 0x7d 0x80 0x81 0x80 0x7d ,0x77 0x75 0x6b 0x6d 0x79 0x74 0x74 0x74 0x6c , 0x81 0x81 0x79 0x7b 0x6f 0x6d 0x6d 0x73 0x71 ,0x63 0x61 0x5d 0x5a 0x65 0x66 0x63 0x67 0x5d , max :0xa4 0xa6 0xa6 0xa6 0x98 0x9a 0x9b 0x97 0x96 ,0x92 0x90 0x84 0x86 0x94 0x8d 0x8f 0x8e 0x85 , 0x9a 0x9a 0x90 0x94 0x89 0x86 0x89 0x8d 0x8b ,0x7d 0x79 0x76 0x72 0x7f 0x7f 0x7a 0x81 0x74 , range:0x36 0x33 0x33 0x34 0x35 0x33 0x33 0x2e 0x31 ,0x36 0x36 0x32 0x32 0x36 0x32 0x35 0x33 0x31 , 0x31 0x31 0x2e 0x32 0x33 0x31 0x37 0x34 0x34 ,0x33 0x30 0x31 0x2f 0x33 0x31 0x2d 0x33 0x2d , cs 1: the read training result: DQS0:0x35, DQS1:0x33, DQS2:0x37, DQS3:0x2e, min :0x13 0x15 0x15 0x12 0x5 0x7 0x9 0x2 , 0xc 0xc 0x1 0x4 0xd 0x6 0xa 0x5 , 0x15 0x17 0x10 0x10 0x5 0x2 0x3 0x4 , 0xd 0xa 0x7 0x2 0xd 0xd 0x8 0xa , mid :0x30 0x31 0x30 0x2d 0x20 0x23 0x24 0x1f ,0x29 0x27 0x1d 0x1f 0x28 0x22 0x26 0x21 , 0x31 0x31 0x2a 0x29 0x1f 0x1c 0x1c 0x1e ,0x29 0x24 0x22 0x1d 0x29 0x28 0x22 0x27 , max :0x4d 0x4d 0x4c 0x49 0x3b 0x3f 0x3f 0x3c ,0x46 0x42 0x39 0x3b 0x44 0x3f 0x42 0x3e , 0x4d 0x4b 0x44 0x42 0x3a 0x36 0x36 0x39 ,0x46 0x3f 0x3e 0x38 0x45 0x43 0x3d 0x44 , range:0x3a 0x38 0x37 0x37 0x36 0x38 0x36 0x3a ,0x3a 0x36 0x38 0x37 0x37 0x39 0x38 0x39 , 0x38 0x34 0x34 0x32 0x35 0x34 0x33 0x35 ,0x39 0x35 0x37 0x36 0x38 0x36 0x35 0x3a , the write training result: DQS0:0x31, DQS1:0x23, DQS2:0x28, DQS3:0xf, min :0x70 0x74 0x74 0x73 0x63 0x68 0x67 0x69 0x66 ,0x5c 0x5d 0x52 0x54 0x60 0x5d 0x59 0x5d 0x55 , 0x6a 0x6a 0x63 0x62 0x57 0x55 0x52 0x59 0x5a ,0x4f 0x4e 0x49 0x47 0x50 0x50 0x4e 0x54 0x4a , mid :0x8a 0x8c 0x8d 0x8b 0x7c 0x80 0x80 0x7f 0x7d ,0x77 0x76 0x6b 0x6d 0x79 0x74 0x73 0x73 0x6f , 0x82 0x82 0x78 0x7a 0x70 0x6d 0x6d 0x71 0x71 ,0x69 0x68 0x63 0x60 0x6b 0x6b 0x65 0x6d 0x62 , max :0xa4 0xa4 0xa6 0xa4 0x96 0x99 0x99 0x96 0x95 ,0x92 0x8f 0x84 0x86 0x92 0x8c 0x8e 0x8a 0x89 , 0x9a 0x9b 0x8d 0x92 0x89 0x85 0x89 0x89 0x89 ,0x84 0x82 0x7d 0x7a 0x86 0x86 0x7d 0x86 0x7b , range:0x34 0x30 0x32 0x31 0x33 0x31 0x32 0x2d 0x2f ,0x36 0x32 0x32 0x32 0x32 0x2f 0x35 0x2d 0x34 , 0x30 0x31 0x2a 0x30 0x32 0x30 0x37 0x30 0x2f ,0x35 0x34 0x34 0x33 0x36 0x36 0x2f 0x32 0x31 , CA Training result: cs:0 min :0x5c 0x50 0x50 0x3b 0x51 0x3b 0x50 ,0x5e 0x4a 0x4d 0x3c 0x50 0x3c 0x55 , cs:0 mid :0x93 0x94 0x85 0x83 0x85 0x80 0x7a ,0x93 0x8f 0x83 0x81 0x84 0x81 0x7c , cs:0 max :0xca 0xd9 0xbb 0xcb 0xba 0xc6 0xa4 ,0xc9 0xd4 0xb9 0xc7 0xb8 0xc6 0xa4 , cs:0 range:0x6e 0x89 0x6b 0x90 0x69 0x8b 0x54 ,0x6b 0x8a 0x6c 0x8b 0x68 0x8a 0x4f , cs:1 min :0x59 0x53 0x4c 0x43 0x4c 0x3e 0x4e ,0x5a 0x50 0x4d 0x41 0x4c 0x42 0x54 , cs:1 mid :0x93 0x93 0x86 0x84 0x86 0x7e 0x79 ,0x94 0x91 0x86 0x81 0x84 0x82 0x7c , cs:1 max :0xcd 0xd3 0xc0 0xc6 0xc1 0xbf 0xa5 ,0xce 0xd3 0xc0 0xc2 0xbd 0xc2 0xa4 , cs:1 range:0x74 0x80 0x74 0x83 0x75 0x81 0x57 ,0x74 0x83 0x73 0x81 0x71 0x80 0x50 , out U-Boot SPL board init U-Boot SPL 2017.09-ga1f6fc00a0-210413 #ldq (Apr 13 2021 - 11:35:00) unknown raw ID phN unrecognized JEDEC id bytes: 00, 00, 00 Trying to boot from MMC2 MMC error: The cmd index is 1, ret is -110 Card did not respond to voltage select! mmc_init: -95, time 9 spl: mmc init failed with error: -95 Trying to boot from MMC1 No misc partition

Verified-boot: 0

Checking atf-1 0x00040000 ... sha256+ OK

Checking uboot 0x00a00000 ... sha256+ OK

Checking fdt 0x00b2d008 ... sha256+ OK

Checking atf-2 0xfdcc9000 ... sha256+ OK

Checking atf-3 0xfdcd0000 ... sha256+ OK

Checking optee 0x08400000 ... sha256+ OK

Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000) Total: 218.792 ms

INFO: Preloader serial: 2 NOTICE: BL31: v2.3():v2.3-135-gcda1658bc-dirty:xsf NOTICE: BL31: Built : 19:32:20, Jun 2 2021 INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: pmu v1 is valid INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: BL31: Initializing runtime services INFO: BL31: Initializing BL32 I/TC: I/TC: OP-TEE version: 3.13.0-630-g631d7ed9a #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #6 Mon Jan 17 19:07:43 CST 2022 aarch64 I/TC: Primary CPU initializing I/TC: Primary CPU switching to normal world boot INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0xa00000 INFO: SPSR = 0x3c9

U-Boot 2017.09-gb2f1de7c96-dirty #xu_yuntong (May 12 2022 - 16:08:39 +0800)

Model: Rockchip RK3568 Evaluation Board PreSerial: 2, raw, 0xfe660000 DRAM: 4 GiB Sysmem: init Relocation Offset: ed34b000 Relocation fdt: eb9f8ce8 - eb9fece0 CR: M/C/I Using default environment

dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0 Bootdev(atags): mmc 0 MMC0: HS200, 200Mhz PartType: EFI DM: v1 No misc partition boot mode: None FIT: No boot partition File not found /extlinux/toybrick.dtb Found DTB in resource part DTB: rk-kernel.dtb HASH(c): OK I2c0 speed: 100000Hz vsel-gpios- not found! Error: -2 vdd_cpu init 900000 uV PMIC: RK8090 (on=0x40, off=0x00) vdd_logic init 900000 uV vdd_gpu init 900000 uV vdd_npu init 900000 uV io-domain: OK get vp0 plane mask:0x22, primary id:5, cursor_plane:-1, from dts get vp1 plane mask:0x15, primary id:4, cursor_plane:-1, from dts get vp2 plane mask:0x8, primary id:3, cursor_plane:-1, from dts Could not find baseparameter partition Model: rockchip,rk3568 Rockchip UBOOT DRM driver version: v1.0.1 vp0 have layer nr:2[1 5 ], primary plane: 5 vp1 have layer nr:3[0 2 4 ], primary plane: 4 vp2 have layer nr:1[3 ], primary plane: 3 Using display timing dts edp@fe0c0000: detailed mode clock 153000 kHz, flags[a] H: 1920 2090 2100 2250 V: 1080 1100 1102 1132 bus_format: 100e VOP update mode to: 1920x1080p0, type: eDP0 for VP1 VOP VP1 enable Smart0[1080x1080->1080x1080@420x0] fmt[1] addr[0xee257000] Link Training success! final link rate = 0x0a, lane count = 0x02 hdmi@fe0a0000 disconnected CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A) apll 1416000 KHz dpll 780000 KHz gpll 1188000 KHz cpll 1000000 KHz npll 1200000 KHz vpll 612000 KHz hpll 24000 KHz ppll 200000 KHz armclk 1416000 KHz aclk_bus 150000 KHz pclk_bus 100000 KHz aclk_top_high 500000 KHz aclk_top_low 400000 KHz hclk_top 150000 KHz pclk_top 100000 KHz aclk_perimid 300000 KHz hclk_perimid 150000 KHz pclk_pmu 100000 KHz No misc partition Net: eth0: ethernet@fe2a0000 Hit key to stop autoboot('CTRL+C'): 0 Could not find misc partition ANDROID: reboot reason: "(none)" optee api revision: 2.0 TEEC: Waring: Could not find security partition Not AVB images, AVB skip android_image_load_by_partname: Can't find part: boot Android image load failed Android boot failed, error -1.

Booting FIT Image FIT: No boot partition

FIT: No fit blob FIT: No FIT image Could not find misc partition Could not find userdata part MMC error: The cmd index is 1, ret is -110..... Card did not respond to voltage select! mmc_init: -95, time 12 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:3... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 215 bytes read in 3 ms (69.3 KiB/s) 1: rockchip-kernel-5.10 Cannot find ohos misc partition Load from partition ' ramdisk ' to address 0xa200000, count: 8192 block(s) Read from partition ' ramdisk ' done, total block(s) 8192 Openharmony ramdisk_addr_r = 0x0a200000:0x400000 Retrieving file: /extlinux/Image 47534088 bytes read in 267 ms (169.8 MiB/s) append: earlycon=uart8250,mmio32,0xfe660000 root=PARTUUID=614e0000-0000-4b53-8000-1d28000054a9 rw rootwait rootfstype=ext4 Retrieving file: /extlinux/rk3568_edp_1920x1080.dtb 165516 bytes read in 5 ms (31.6 MiB/s) Fdt Ramdisk skip relocation No misc partition

Flattened Device Tree blob at 0x0a100000

Booting using the fdt blob at 0x0a100000 'reserved-memory' ramoops@110000: addr=110000 size=f0000 Using Device Tree in place at 000000000a100000, end 000000000a12b68b Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000) Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000) Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000) Total: 1069.946 ms

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux version 5.10.165 (lubancat@lubancat-vm) (OHOS (dev) clang version 15.0.4 (llvm-project d1aa604d90b55a96aa22af9992d170fccbd41938), LLD 15.0.4) #1 SMP Thu Jul 25 10:13:29 CST 2024 [ 0.000000] Machine model: rockchip,rk3568 [ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000200000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000001ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000083fffff] [ 0.000000] node 0: [mem 0x0000000009400000-0x00000000efffffff] [ 0.000000] node 0: [mem 0x00000001f0000000-0x00000001ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff] [ 0.000000] cma: Reserved 16 MiB at 0x00000000ecc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 31 pages/cpu s88232 r8192 d30552 u126976 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: patching kernel code [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1027656 [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xfe660000 root=PARTUUID=614e0000-0000 rw rootwait rootfstype=ext4 console=ttyFIQ0 hardware=rk3568 default_boot_device=fe310000.sdhci bootslots=2 ohos.required_mount.system=/dev/block/platform/fe310000.sdhci/by-name/system@/usr@ext4@ro,barrier=1@wait,required ohos.required_mount.vendor=/dev/block/platform/fe310000.sdhci/by-name/vendor@/vendor@ext4@ro,barrier=1@wait,required ohos.required_mount.misc=/dev/block/platform/fe310000.sdhci/by-name/misc@none@none@none@wait,required [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000e8c00000-0x00000000ecc00000] (64MB) [ 0.000000] Memory: 3931036K/4175872K available (22652K kernel code, 3988K rwdata, 18060K rodata, 1664K init, 675K bss, 228452K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 62868 entries in 246 pages [ 0.000000] ftrace: allocated 246 pages with 6 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 320 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000 [ 0.000000] ITS [mem 0xfd440000-0xfd45ffff] [ 0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @210000 (indirect, esz 8, psz 64K, shr 0) [ 0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @220000 (flat, esz 2, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000000000230000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000000240000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001972] Console: colour dummy device 80x25 [ 0.002417] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000) [ 0.003362] pid_max: default: 32768 minimum: 301 [ 0.003869] LSM: Security Framework initializing [ 0.004326] SELinux: Initializing. [ 0.004749] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.005464] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.008092] rcu: Hierarchical SRCU implementation. [ 0.009593] Platform MSI: interrupt-controller@fd440000 domain created [ 0.010621] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created [ 0.012208] smp: Bringing up secondary CPUs ... I/TC: Secondary CPU 1 initializing I/TC: Secondary CPU 1 switching to normal world boot I/TC: Secondary CPU 2 initializing I/TC: Secondary CPU 2 switching to normal world boot I/TC: Secondary CPU 3 initializing I/TC: Secondary CPU 3 switching to normal world boot [ 0.014006] Detected VIPT I-cache on CPU1 [ 0.014040] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000 [ 0.014059] GICv3: CPU1: using allocated LPI pending table @0x0000000000250000 [ 0.014114] CPU1: Booted secondary processor 0x0000000100 [0x412fd050] [ 0.015604] Detected VIPT I-cache on CPU2 [ 0.015631] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000 [ 0.015649] GICv3: CPU2: using allocated LPI pending table @0x0000000000260000 [ 0.015693] CPU2: Booted secondary processor 0x0000000200 [0x412fd050] [ 0.017171] Detected VIPT I-cache on CPU3 [ 0.017197] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000 [ 0.017213] GICv3: CPU3: using allocated LPI pending table @0x0000000000270000 [ 0.017255] CPU3: Booted secondary processor 0x0000000300 [0x412fd050] [ 0.017411] smp: Brought up 1 node, 4 CPUs [ 0.024622] SMP: Total of 4 processors activated. [ 0.025056] CPU features: detected: Privileged Access Never [ 0.025568] CPU features: detected: User Access Override [ 0.026055] CPU features: detected: 32-bit EL0 Support [ 0.026553] CPU features: detected: Common not Private translations [ 0.027131] CPU features: detected: RAS Extension Support [ 0.027628] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.028418] CPU features: detected: CRC32 instructions [ 0.028891] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.029621] CPU: All CPU(s) started at EL2 [ 0.031508] devtmpfs: initialized [ 0.055962] Registered cp15_barrier emulation handler [ 0.056452] Registered setend emulation handler [ 0.056877] KASLR disabled due to lack of seed [ 0.057600] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.058519] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.059819] pinctrl core: initialized pinctrl subsystem [ 0.061298] bbox:[info][blackbox_core.c:262] wait for log part [/data] begin! [ 0.062193] NET: Registered protocol family 16 [ 0.064116] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.064880] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.065777] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.066555] audit: initializing netlink subsys (disabled) [ 0.067286] audit: type=2000 audit(0.063:1): state=initialized audit_enabled=0 res=1 [ 0.069831] thermal_sys: Registered thermal governor 'fair_share' [ 0.069840] thermal_sys: Registered thermal governor 'step_wise' [ 0.071076] cpuidle: using governor menu [ 0.072012] Registered FIQ tty driver [ 0.072400] bbox:[info][blackbox_core.c:514] [SYSTEM] is registered successfully! [ 0.073790] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.074572] ASID allocator initialised with 65536 entries [ 0.077833] printk: console [ramoops-1] enabled [ 0.078254] pstore: Registered ramoops as persistent store backend [ 0.078823] ramoops: using 0xf0000@0x110000, ecc: 0 [ 0.133343] rockchip-gpio fdd60000.gpio0: probed gpio0 (fdd60000.gpio0) [ 0.135481] rockchip-gpio fe740000.gpio1: probed gpio1 (fe740000.gpio1) [ 0.137578] rockchip-gpio fe750000.gpio2: probed gpio2 (fe750000.gpio2) [ 0.139481] rockchip-gpio fe760000.gpio3: probed gpio3 (fe760000.gpio3) [ 0.141262] rockchip-gpio fe770000.gpio4: probed gpio4 (fe770000.gpio4) [ 0.142025] rockchip-pinctrl pinctrl: probed pinctrl [ 0.159606] cryptd: max_cpu_qlen set to 1000 [ 0.165299] fiq_debugger fiq_debugger.0: IRQ fiq not found [ 0.165837] fiq_debugger fiq_debugger.0: IRQ wakeup not found [[ 0.166470] printk: console [ttyFIQ0] enabled 0.166470] printk: console [ttyFIQ0] enabled [ 0.167264] printk: bootconsole [uart8250] disabled [ 0.167264] printk: bootconsole [uart8250] disabled [ 0.167966] Registered fiq debugger ttyFIQ0 [ 0.169265] vcc3v3_sys: supplied by dc_12v [ 0.169808] vcc5v0_sys: supplied by dc_12v [ 0.173468] vcc2v5-sys: supplied by vcc3v3_sys [ 0.173914] vcc3v3_bu: supplied by vcc5v0_sys [ 0.175622] iommu: Default domain type: Translated [ 0.175940] rk_iommu fdea0800.iommu: version = 2 [ 0.176536] rk_iommu fded0480.iommu: version = 2 [ 0.176852] rk_iommu fdee0800.iommu: version = 2 [ 0.177148] rk_iommu fdef0800.iommu: version = 2 [ 0.177459] rk_iommu fdf40f00.iommu: version = 2 [ 0.177818] rk_iommu fdf80800.iommu: version = 2 [ 0.178170] rk_iommu fdfe0800.iommu: version = 2 [ 0.178474] rk_iommu fdff1a00.iommu: version = 2 [ 0.178753] rk_iommu fe043e00.iommu: version = 2 [ 0.179592] SCSI subsystem initialized [ 0.179848] usbcore: registered new interface driver usbfs [ 0.179899] usbcore: registered new interface driver hub [ 0.179951] usbcore: registered new device driver usb [ 0.180017] mc: Linux media interface: v0.10 [ 0.180058] videodev: Linux video capture interface: v2.00 [ 0.180143] pps_core: LinuxPPS API ver. 1 registered [ 0.180153] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.180175] PTP clock support registered [ 0.180938] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled. [ 0.180999] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0 [ 0.183456] Bluetooth: Core ver 2.22 [ 0.183510] NET: Registered protocol family 31 [ 0.183520] Bluetooth: HCI device and connection manager initialized [ 0.183537] Bluetooth: HCI socket layer initialized [ 0.183549] Bluetooth: L2CAP socket layer initialized [ 0.183574] Bluetooth: SCO socket layer initialized [ 0.184017] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 0.185063] clocksource: Switched to clocksource arch_sys_counter [ 0.637718] VFS: Disk quotas dquot_6.6.0 [ 0.637828] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.648188] NET: Registered protocol family 2 [ 0.648480] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.650822] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 81920 bytes, linear) [ 0.651038] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.651435] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) [ 0.652203] TCP: Hash tables configured (established 32768 bind 32768) [ 0.652476] UDP hash table entries: 2048 (order: 5, 196608 bytes, linear) [ 0.652694] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes, linear) [ 0.653030] NET: Registered protocol family 1 [ 0.653734] RPC: Registered named UNIX socket transport module. [ 0.653749] RPC: Registered udp transport module. [ 0.653757] RPC: Registered tcp transport module. [ 0.653764] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.654743] PCI: CLS 0 bytes, default 64 [ 0.655512] Trying to unpack rootfs image as initramfs... [ 0.745876] Freeing initrd memory: 4096K [ 0.747031] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available [ 0.753969] Initialise system trusted keyrings [ 0.754251] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.761012] hmdfs: hmdfs_init_configfs() init configfs [ 0.761130] Registering sharefs [ 0.761214] sharefs: sharefs_init_configfs() init configfs [ 0.761482] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.762444] NFS: Registering the id_resolver key type [ 0.762488] Key type id_resolver registered [ 0.762499] Key type id_legacy registered [ 0.762538] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.762708] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.763031] fuse: init (API version 7.32) [ 0.763455] SGI XFS with security attributes, no debug enabled [ 0.766154] [I/xpm_kernel]xpm_module_init: xpm module init success [ 0.797103] NET: Registered protocol family 38 [ 0.797136] Key type asymmetric registered [ 0.797147] Asymmetric key parser 'x509' registered [ 0.797193] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242) [ 0.797206] io scheduler mq-deadline registered [ 0.797215] io scheduler kyber registered [ 0.798005] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully! [ 0.798683] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully! [ 0.811248] pwm-backlight backlight: supply power not found, using dummy regulator [ 0.811867] pwm-backlight backlight1: supply power not found, using dummy regulator [ 0.812369] mpp_service mpp-srv: [ 0.812386] mpp_service mpp-srv: probe start [ 0.814092] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 4 [ 0.814359] mpp_rkvenc fdf40000.rkvenc: probing start [ 0.814674] mpp_rkvenc fdf40000.rkvenc: venc regulator not ready, retry [ 0.814687] rkvenc_init:1203: failed to add venc devfreq [ 0.815168] mpp_rkvenc fdf40000.rkvenc: probing finish [ 0.816264] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 0 [ 0.816470] mpp_vdpu2 fdea0400.vdpu: probe device [ 0.817054] mpp_vdpu2 fdea0400.vdpu: probing finish [ 0.817693] mpp_vepu2 fdee0000.vepu: Adding to iommu group 2 [ 0.817912] mpp_vepu2 fdee0000.vepu: probing start [ 0.818509] mpp_vepu2 fdee0000.vepu: probing finish [ 0.819172] mpp-iep2 fdef0000.iep: Adding to iommu group 3 [ 0.819356] mpp-iep2 fdef0000.iep: probe device [ 0.819689] mpp-iep2 fdef0000.iep: allocate roi buffer failed [ 0.819953] mpp-iep2 fdef0000.iep: probing finish [ 0.820571] mpp_jpgdec fded0000.jpegd: Adding to iommu group 1 [ 0.820740] mpp_jpgdec fded0000.jpegd: probe device [ 0.821301] mpp_jpgdec fded0000.jpegd: probing finish [ 0.822035] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 5 [ 0.822297] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start [ 0.822668] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found! [ 0.822682] rkvdec2_init:687: No niu aclk reset resource define [ 0.822694] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found! [ 0.822703] rkvdec2_init:690: No niu hclk reset resource define [ 0.822868] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000 [ 0.822881] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000 [ 0.822891] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056 [ 0.822900] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536 [ 0.822911] mpp_rkvdec2 fdf80200.rkvdec: min_width 512 [ 0.822923] mpp_rkvdec2 fdf80200.rkvdec: link mode resource not found [ 0.823241] mpp_rkvdec2 fdf80200.rkvdec: probing finish [ 0.823996] mpp_service mpp-srv: probe success [ 0.829614] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330 [ 0.829641] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16 [ 0.831739] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330 [ 0.831778] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16 [ 0.833200] rockchip-pvtm fde00000.pvtm: pvtm@0 probed [ 0.833366] rockchip-pvtm fde80000.pvtm: pvtm@1 probed [ 0.833496] rockchip-pvtm fde90000.pvtm: pvtm@2 probed [ 0.834351] rockchip-system-monitor rockchip-system-monitor: system monitor probe [ 0.835204] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.836165] fdd50000.serial: ttyS0 at MMIO 0xfdd50000 (irq = 24, base_baud = 1500000) is a 16550A [ 0.837521] fe680000.serial: ttyS4 at MMIO 0xfe680000 (irq = 72, base_baud = 1500000) is a 16550A [ 0.838659] fe6b0000.serial: ttyS7 at MMIO 0xfe6b0000 (irq = 73, base_baud = 1500000) is a 16550A [ 0.841402] rockchip-vop2 fe040000.vop: Adding to iommu group 8 [ 0.849095] no ATF memory for init [ 0.849939] mali fde60000.gpu: Kernel DDK version g2p0-01eac0 [ 0.850037] mali fde60000.gpu: Power management initialization failed error = -517 [ 0.850060] mali fde60000.gpu: Device initialization Deferred [ 0.850503] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.851295] brd: module loaded [ 0.858043] loop: module loaded [ 0.858549] zram: Added device: zram0 [ 0.858909] lkdtm: No crash points registered, enable through debugfs [ 0.862666] tun: Universal TUN/TAP device driver, 1.6 [ 0.864169] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 0.864503] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 0.864518] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input). [ 0.864530] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. [ 0.864539] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0xffffffff [ 0.864549] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. [ 0.864559] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0xffffffff [ 0.864575] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 0.864613] rk_gmac-dwmac fe2a0000.ethernet: cannot get clock clk_mac_ref [ 0.864631] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY [ 0.864873] rk_gmac-dwmac fe2a0000.ethernet: init for RMII [ 0.865202] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 0.865219] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 0.865232] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register supported [ 0.865243] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine supported [ 0.865252] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 0.865261] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 0.865337] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 0.865349] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.865360] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 0.865370] rk_gmac-dwmac fe2a0000.ethernet: Using 32 bits DMA width [ 1.002063] usbcore: registered new interface driver rndis_wlan [ 1.002152] usbcore: registered new interface driver rtl8150 [ 1.002199] usbcore: registered new interface driver r8152 [ 1.002244] usbcore: registered new interface driver asix [ 1.002289] usbcore: registered new interface driver ax88179_178a [ 1.002329] usbcore: registered new interface driver cdc_ether [ 1.002370] usbcore: registered new interface driver net1080 [ 1.002410] usbcore: registered new interface driver rndis_host [ 1.002450] usbcore: registered new interface driver cdc_subset [ 1.002489] usbcore: registered new interface driver zaurus [ 1.019154] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.019202] ehci-pci: EHCI PCI platform driver [ 1.019275] ehci-platform: EHCI generic platform driver [ 1.019677] phy phy-fe8b0000.usb2-phy.4: illegal mode [ 1.021964] ehci-platform fd800000.usb: EHCI Host Controller [ 1.022216] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1 [ 1.022362] ehci-platform fd800000.usb: irq 19, io mem 0xfd800000 [ 1.035105] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00 [ 1.035400] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 1.035414] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.035425] usb usb1: Product: EHCI Host Controller [ 1.035434] usb usb1: Manufacturer: Linux 5.10.165 ehci_hcd [ 1.035443] usb usb1: SerialNumber: fd800000.usb [ 1.035975] hub 1-0:1.0: USB hub found [ 1.036026] hub 1-0:1.0: 1 port detected [ 1.039164] ehci-platform fd880000.usb: EHCI Host Controller [ 1.039416] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2 [ 1.039574] ehci-platform fd880000.usb: irq 21, io mem 0xfd880000 [ 1.051727] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00 [ 1.052008] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 1.052022] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.052032] usb usb2: Product: EHCI Host Controller [ 1.052042] usb usb2: Manufacturer: Linux 5.10.165 ehci_hcd [ 1.052051] usb usb2: SerialNumber: fd880000.usb [ 1.052555] hub 2-0:1.0: USB hub found [ 1.052606] hub 2-0:1.0: 1 port detected [ 1.053660] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.053700] ohci-platform: OHCI generic platform driver [ 1.054029] phy phy-fe8b0000.usb2-phy.4: illegal mode [ 1.054049] ohci-platform fd840000.usb: Generic Platform OHCI controller [ 1.054275] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3 [ 1.054402] ohci-platform fd840000.usb: irq 20, io mem 0xfd840000 [ 1.112605] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10 [ 1.112630] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.112642] usb usb3: Product: Generic Platform OHCI controller [ 1.112652] usb usb3: Manufacturer: Linux 5.10.165 ohci_hcd [ 1.112662] usb usb3: SerialNumber: fd840000.usb [ 1.113209] hub 3-0:1.0: USB hub found [ 1.113261] hub 3-0:1.0: 1 port detected [ 1.114022] ohci-platform fd8c0000.usb: Generic Platform OHCI controller [ 1.114254] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4 [ 1.114388] ohci-platform fd8c0000.usb: irq 22, io mem 0xfd8c0000 [ 1.172604] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10 [ 1.172628] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.172640] usb usb4: Product: Generic Platform OHCI controller [ 1.172650] usb usb4: Manufacturer: Linux 5.10.165 ohci_hcd [ 1.172659] usb usb4: SerialNumber: fd8c0000.usb [ 1.173176] hub 4-0:1.0: USB hub found [ 1.173227] hub 4-0:1.0: 1 port detected [ 1.175194] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.175430] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5 [ 1.175591] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010 [ 1.175656] xhci-hcd xhci-hcd.0.auto: irq 86, io mem 0xfd000000 [ 1.176039] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 1.176054] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.176064] usb usb5: Product: xHCI Host Controller [ 1.176073] usb usb5: Manufacturer: Linux 5.10.165 xhci-hcd [ 1.176082] usb usb5: SerialNumber: xhci-hcd.0.auto [ 1.176589] hub 5-0:1.0: USB hub found [ 1.176641] hub 5-0:1.0: 1 port detected [ 1.177002] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.177187] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6 [ 1.177210] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.177302] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.177483] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 1.177497] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.177507] usb usb6: Product: xHCI Host Controller [ 1.177516] usb usb6: Manufacturer: Linux 5.10.165 xhci-hcd [ 1.177525] usb usb6: SerialNumber: xhci-hcd.0.auto [ 1.178008] hub 6-0:1.0: USB hub found [ 1.178055] hub 6-0:1.0: 1 port detected [ 1.178786] usbcore: registered new interface driver uas [ 1.178921] usbcore: registered new interface driver usb-storage [ 1.179042] usbcore: registered new interface driver usbserial_generic [ 1.179072] usbserial: USB Serial support registered for generic [ 1.179132] usbcore: registered new interface driver cp210x [ 1.179160] usbserial: USB Serial support registered for cp210x [ 1.179246] usbcore: registered new interface driver ftdi_sio [ 1.179274] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.179467] usbcore: registered new interface driver keyspan [ 1.179499] usbserial: USB Serial support registered for Keyspan - (without firmware) [ 1.179525] usbserial: USB Serial support registered for Keyspan 1 port adapter [ 1.179553] usbserial: USB Serial support registered for Keyspan 2 port adapter [ 1.179579] usbserial: USB Serial support registered for Keyspan 4 port adapter [ 1.179636] usbcore: registered new interface driver option [ 1.179665] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.179935] usbcore: registered new interface driver oti6858 [ 1.179964] usbserial: USB Serial support registered for oti6858 [ 1.180020] usbcore: registered new interface driver pl2303 [ 1.180048] usbserial: USB Serial support registered for pl2303 [ 1.180109] usbcore: registered new interface driver qcserial [ 1.180138] usbserial: USB Serial support registered for Qualcomm USB modem [ 1.180210] usbcore: registered new interface driver sierra [ 1.180243] usbserial: USB Serial support registered for Sierra USB modem [ 1.181373] usbcore: registered new interface driver usbtouchscreen [ 1.182326] i2c /dev entries driver [ 1.185138] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected! [ 1.186945] vdd_cpu: supplied by vcc5v0_sys [ 1.194969] rk808 0-0020: chip id: 0x8090 [ 1.195063] rk808 0-0020: No cache defaults, reading back from HW [ 1.218806] rk808 0-0020: source: on=0x40, off=0x00 [ 1.218837] rk808 0-0020: support dcdc3 fb mode:-22, 0 [ 1.218852] rk808 0-0020: support pmic reset mode:0,0 [ 1.224894] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 1.224951] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 1.225605] vdd_logic: supplied by vcc3v3_sys [ 1.226754] vdd_gpu: supplied by vcc3v3_sys [ 1.227490] vcc_ddr: supplied by vcc3v3_sys [ 1.228208] vdd_npu: supplied by vcc3v3_sys [ 1.229290] vcc_1v8: supplied by vcc3v3_sys [ 1.229999] vdda0v9_image: supplied by vcc3v3_sys [ 1.231565] vdda_0v9: supplied by vcc3v3_sys [ 1.232785] vdda0v9_pmu: supplied by vcc3v3_sys [ 1.234007] vccio_acodec: supplied by vcc3v3_sys [ 1.235603] vccio_sd: supplied by vcc3v3_sys [ 1.236834] vcc3v3_pmu: supplied by vcc3v3_sys [ 1.238414] vcca_1v8: supplied by vcc3v3_sys [ 1.239748] vcca1v8_pmu: supplied by vcc3v3_sys [ 1.240966] vcca1v8_image: supplied by vcc3v3_sys [ 1.242551] vcc_3v3: supplied by vcc3v3_sys [ 1.243589] vcc3v3_sd: supplied by vcc3v3_sys [ 1.244256] rk817-battery: Failed to locate of_node [id: -1] [ 1.244418] rk817-battery rk817-battery: Failed to find matching dt id [ 1.244526] rk817-charger: Failed to locate of_node [id: -1] [ 1.244630] rk817-charger rk817-charger: Failed to find matching dt id [ 1.247770] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0 [ 1.248128] [E/HDF_LOG_TAG] SetInputDevAbility: match cached info failed [ 1.254341] rk808-rtc rk808-rtc: registered as rtc0 [ 1.256106] rk808-rtc rk808-rtc: setting system clock to 2017-08-05T09:00:03 UTC (1501923603) [ 1.258561] i2c i2c-1: 1 i2c clients have been registered at 0x40 [ 1.269995] rtc-hym8563 5-0051: registered as rtc1 [ 1.273430] OF: graph: no port node found in /mipi-csi2@fdfb0000 [ 1.273484] rockchip-mipi-csi2: probe success, v4l2_dev:(efault)! [ 1.274081] rkisp_hw fdff0000.rkisp: Adding to iommu group 7 [ 1.274316] rkisp_hw fdff0000.rkisp: is_thunderboot: 0 [ 1.274331] rkisp_hw fdff0000.rkisp: max input:0x0@0fps [ 1.274363] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff] [ 1.275454] rkisp rkisp-vir0: rkisp driver version: v01.08.00 [ 1.275587] rkisp rkisp-vir0: No memory-region-thunderboot specified [ 1.275828] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized! [ 1.275852] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized! [ 1.278545] usbcore: registered new interface driver uvcvideo [ 1.278568] USB Video Class driver (1.1.1) [ 1.281606] rockchip-thermal fe710000.tsadc: tsadc is probed successfully! [ 1.283255] Bluetooth: HCI UART driver ver 2.3 [ 1.283289] Bluetooth: HCI UART protocol H4 registered [ 1.283299] Bluetooth: HCI UART protocol ATH3K registered [ 1.283384] usbcore: registered new interface driver bfusb [ 1.283447] usbcore: registered new interface driver btusb [ 1.283761] cpu cpu0: Failed to get cpu_leakage [ 1.298506] cpu cpu0: temp=31875, pvtm=85097 (85331 + -234) [ 1.298841] cpu cpu0: pvtm-volt-sel=1 [ 1.300743] cpu cpu0: avs=0 [ 1.301123] cpu cpu0: EM: created perf domain [ 1.301263] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0 [ 1.307465] sdhci: Secure Digital Host Controller Interface driver [ 1.307505] sdhci: Copyright(c) Pierre Ossman [ 1.307514] Synopsys Designware Multimedia Card Interface Driver [ 1.308341] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.309040] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode. [ 1.309105] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller. [ 1.309121] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a [ 1.309146] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode. [ 1.309178] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller. [ 1.309190] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 52,32 bit host data width,256 deep fifo [ 1.309199] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a [ 1.309242] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 56,32 bit host data width,256 deep fifo [ 1.309637] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq [ 1.309659] mmc_host mmc3: card is non-removable. [ 1.310270] SMCCC: SOC_ID: ARCH_FEATURES(ARCH_SOC_ID) returned error: fffffffffffffffd [ 1.310734] hid: raw HID events driver (C) Jiri Kosina [ 1.311223] usbcore: registered new interface driver usbhid [ 1.311240] usbhid: USB HID core driver [ 1.311723] ashmem: initialized [ 1.311959] zrhung hung_wp_screen_init start [ 1.312226] zrhung hung_wp_screen_init done [ 1.312747] rockchip,bus bus-npu: Failed to get leakage [ 1.312769] rockchip,bus bus-npu: pvtm = 85097, form pvtm_value [ 1.312786] rockchip,bus bus-npu: pvtm-volt-sel=1 [ 1.313023] rockchip,bus bus-npu: avs=0 [ 1.317804] optee: probing for conduit method. [ 1.317845] optee: revision 3.13 (631d7ed9) [ 1.318289] optee: initialized driver [ 1.318970] auth_ctrl init success [ 1.318990] [QOS_CTRL] lock in qos policy initialized [ 1.319921] usbcore: registered new interface driver hdf-audio-usb [ 1.320543] rk817-codec rk817-codec: DMA mask not set [ 1.321126] rk817-codec rk817-codec: got rk817-codec platform_device [ 1.322154] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)

[ 1.324067] access_token_id: access_tokenid init success [ 1.325094] xt_time: kernel timezone is -0000 [ 1.325478] Initializing XFRM netlink socket [ 1.325903] NET: Registered protocol family 10 [ 1.326997] Segment Routing with IPv6 [ 1.327106] NET: Registered protocol family 17 [ 1.327135] NET: Registered protocol family 15 [ 1.327380] Bluetooth: RFCOMM socket layer initialized [ 1.327426] Bluetooth: RFCOMM ver 1.11 [ 1.327446] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.327461] Bluetooth: HIDP socket layer initialized [ 1.327734] [BT_RFKILL]: Enter rfkill_rk_init [ 1.327746] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 1.328530] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 1.328591] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6275s [ 1.328602] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 1.328612] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 1.328656] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 124, flags = 0. [ 1.328671] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found ! [ 1.328680] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 1.328691] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1 [ 1.328699] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 1.329701] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 20. [ 1.329744] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 96. [ 1.329763] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 98. [ 1.329782] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 97. [ 1.329884] [BT_RFKILL]: Request irq for bt wakeup host [ 1.329999] [BT_RFKILL]: ** disable irq [ 1.330138] [BT_RFKILL]: bt_default device registered. [ 1.330455] Key type dns_resolver registered [ 1.330670] NET: Registered protocol family 45 [ 1.332106] core_ctl: Creating CPU group 0 [ 1.332125] core_ctl: Init CPU0 state [ 1.332133] core_ctl: Init CPU1 state [ 1.332140] core_ctl: Init CPU2 state [ 1.332146] core_ctl: Init CPU3 state [ 1.332804] Loading compiled-in X.509 certificates [ 1.335838] Loaded X.509 cert 'Build time autogenerated kernel key: 629155bc8a06d906ea6984c99a17639ebb5f5d03' [ 1.336122] run reclaimacct_init successfully [ 1.336132] enabled [ 1.336189] Key type .fscrypt registered [ 1.336200] Key type fscrypt-provisio [ 1.376985] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.377453] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.379648] mali fde60000.gpu: Kernel DDK version g2p0-01eac0 [ 1.380010] mali fde60000.gpu: dev_pm_opp_set_regulators: no regulator (shadercores) found: -19 [ 1.380100] mali fde60000.gpu: Failed to get gpu_leakage [ 1.380559] mali fde60000.gpu: avs=0 [ 1.380576] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 112; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available. [ 1.380953] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0 [ 1.381040] mali fde60000.gpu: No memory group manager is configured [ 1.381488] mali fde60000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0 [ 1.381526] mali fde60000.gpu: Failed to get gpu_leakage [ 1.382636] mali fde60000.gpu: Probed as mali0 [ 1.383240] input: adc-keys as /devices/platform/adc-keys/input/input1 [ 1.383952] of_clk_hw_onecell_get: invalid index 3 [ 1.383968] rockchip-dmc dmc: Cannot get the clk dmc_clk. If using SCMI, trusted firmware need update to V1.01 and above. [ 1.384066] rockchip-dmc: probe of dmc failed with error -2 [ 1.384597] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.384953] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.385905] rk_iommu fde4b000.iommu: deferred probe timeout, ignoring dependency [ 1.385926] rk_iommu: probe of fde4b000.iommu failed with error -110 [ 1.386163] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.386460] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.387623] [dhd] dhd_module_init: in Dongle Host Driver, version 100.10.545.19 (r826445-20210310-3) [ 1.387642] [dhd] ======== dhd_wlan_init_plat_data ======== [ 1.387649] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter [ 1.387699] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=114, oob_irq_flags=0x414 [ 1.387707] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1 [ 1.387712] [dhd] dhd_wifi_platform_load: Enter [ 1.387718] [dhd] Power-up adapter 'DHD generic adapter' [ 1.387747] [dhd] wifi_platform_set_power = 1, delay: 200 msec [ 1.387755] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 1.387761] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 1.387767] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false [ 1.387773] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0] [ 1.410896] mmc0: new HS200 MMC card at address 0001 [ 1.411513] mmcblk0: mmc0:0001 BJTD4R 29.1 GiB [ 1.411819] mmcblk0boot0: mmc0:0001 BJTD4R partition 1 4.00 MiB [ 1.412047] mmcblk0boot1: mmc0:0001 BJTD4R partition 2 4.00 MiB [ 1.412256] mmcblk0rpmb: mmc0:0001 BJTD4R partition 3 4.00 MiB, chardev (237:0) [ 1.415389] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 [ 1.419742] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.420199] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.428689] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0) [ 1.442198] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.442593] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.473387] mmc3: queuing unknown CIS tuple 0x80 (2 bytes) [ 1.475067] mmc3: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.476765] mmc3: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.479784] mmc3: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.482182] devfreq fde60000.gpu: Couldn't update frequency transition information. [ 1.578664] mmc_host mmc3: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0) [ 1.591920] usb 3-1: new full-speed USB device number 2 using ohci-platform [ 1.691942] [dhd] wifi_platform_bus_enumerate device present 1 [ 1.692028] [dhd] ======== Card detection to detect SDIO card! ======== [ 1.692058] sdio: host isn't initialization successfully. [ 1.822119] usb 3-1: New USB device found, idVendor=222a, idProduct=0001, bcdDevice= 0.02 [ 1.822208] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.822248] usb 3-1: Product: ILITEK-TP [ 1.822279] usb 3-1: Manufacturer: ILITEK [ 1.840899] input: ILITEK ILITEK-TP as /devices/platform/fd840000.usb/usb3/3-1/3-1:1.0/0003:222A:0001.0001/input/input2 [ 1.842340] input: ILITEK ILITEK-TP Mouse as /devices/platform/fd840000.usb/usb3/3-1/3-1:1.0/0003:222A:0001.0001/input/input4 [ 1.844405] hid-multitouch 0003:222A:0001.0001: input,hiddev96,hidraw0: USB HID v1.10 Mouse [ILITEK ILITEK-TP] on usb-fd840000.usb-1/input0 [ 1.846325] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.847633] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.868814] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 202 [ 1.880205] mmc3: new ultra high speed SDR104 SDIO card at address 0001 [ 1.882705] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.884022] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.887766] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.889114] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.903628] [dhd] bcmsdh_register: register client driver [ 1.904517] [dhd] bcmsdh_sdmmc_probe: Enter num=1 [ 1.905419] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.905578] [dhd] bcmsdh_sdmmc_probe: Enter num=2 [ 1.905619] [dhd] bus num (host idx)=3, slot num (rca)=1 [ 1.905648] [dhd] found adapter info 'DHD generic adapter' [ 1.905775] [dhd] sdioh_attach: set sd_f2_blocksize 256 [ 1.905877] [dhd] sdioh_attach: sd clock rate = 0 [ 1.906693] [dhd] dhdsdio_probe : no mutex held. set lock [ 1.906716] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.906967] [dhd] F1 signature read @0x18000000=0x1042aae8 [ 1.915627] [dhd] F1 signature OK, socitype:0x1 chip:0xaae8 rev:0x2 pkg:0x4 [ 1.917268] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000 [ 1.917551] [dhd] dhd_conf_set_chiprev : devid=0xaae8, chip=0xaae8, chiprev=2 [ 1.917733] [dhd] dhd_allocate_if: bdh6: create netdevice wlan%d ifidx=0, bssidx=0 [ 1.920241] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 1.920331] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 1.921865] [dhd] dhd_log_dump_init: kernel log buf size = 256KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 38KB [ 1.928184] [dhd] dhd_attach(): thread:dhd_watchdog_thread:c9 started [ 1.928991] [dhd] dhd_attach(): thread:dhd_dpc:ca started [ 1.929728] [dhd] dhd_attach(): thread:dhd_rxf:cb started [ 1.929813] [dhd] dhd_deferred_work_init: work queue initialized [ 1.929861] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2 [ 1.930082] [dhd] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist [ 1.930130] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3 [ 1.930177] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x1070 [ 1.946159] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN [ 1.946443] [dhd] dhd_register_if: bdh6 register netdev=wlan%d ifidx=0 [ 1.946478] [dhd] Dongle Host Driver, version 100.10.545.19 (r826445-20210310-3) [ 1.947999] [dhd] dhd_dbg_detach_pkt_monitor, 2100 [ 1.948039] [dhd] dhd_bus_devreset: == Power OFF == [ 1.948496] [dhd] dhd_bus_stop: making DHD_BUS_DOWN [ 1.948575] [dhd] bcmsdh_oob_intr_unregister: Enter [ 1.948597] [dhd] bcmsdh_oob_intr_unregister: irq is not registered [ 1.948626] [dhd] dhd_bus_devreset: making dhdpub up FALSE [ 1.948652] [dhd] dhd_txglom_enable: enable 0 [ 1.948670] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN [ 1.948691] [dhd] dhd_bus_devreset: WLAN OFF DONE [ 1.948769] [dhd] wifi_platform_set_power = 0, delay: 0 msec [ 1.948800] [dhd] ======== PULL WL_REG_ON(-1) LOW! ======== [ 1.948818] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 1.948837] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false [ 1.948855] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1] [ 1.948874] [dhd] dhdsdio_probe : the lock is released. [ 1.949518] rockchip-cpuinfo cpuinfo: failed to get id cell: -517 [ 1.950416] pwm-backlight backlight1: supply power not found, using dummy regulator [ 1.952163] [dhd] dhd_module_init: Exit err=0 [ 1.953798] [I/osal_cdev] register hdf class success [ 1.954475] [I/osal_cdev] add cdev dev_mgr success [ 1.954475] [ 1.954920] [I/osal_cdev] add cdev devsvc_mgr success [ 1.954920] [ 1.954957] [I/devmgr_service] start svcmgr result 0 [ 1.954985] [I/hcs_blob_if] CheckHcsBlobLength: the blobLength: 63352, byteAlign: 1 [ 1.956714] [I/device_node] launch devnode [ 1.956746] [I/linux_gpio_adapter] LinuxGpioMatchProbe: find gpio chip(start:0, count:32) [ 1.956900] [I/gpio_manager] GpioManagerAdd: start:0 count:32 added success! [ 1.956952] [I/linux_gpio_adapter] LinuxGpioMatchProbe: add gpio controller(start:0, count:32) succeed! [ 1.956974] [I/linux_gpio_adapter] LinuxGpioMatchProbe: find gpio chip(start:32, count:32) [ 1.957099] [I/gpio_manager] GpioManagerAdd: start:32 count:32 added success! [ 1.957145] [I/linux_gpio_adapter] LinuxGpioMatchProbe: add gpio controller(start:32, count:32) succeed! [ 1.957167] [I/linux_gpio_adapter] LinuxGpioMatchProbe: find gpio chip(start:64, count:32) [ 1.957291] [I/gpio_manager] GpioManagerAdd: start:64 count:32 added success! [ 1.957339] [I/linux_gpio_adapter] LinuxGpioMatchProbe: add gpio controller(start:64, count:32) succeed! [ 1.957361] [I/linux_gpio_adapter] LinuxGpioMatchProbe: find gpio chip(start:96, count:32) [ 1.957480] [I/gpio_manager] GpioManagerAdd: start:96 count:32 added success! [ 1.957528] [I/linux_gpio_adapter] LinuxGpioMatchProbe: add gpio controller(start:96, count:32) succeed! [ 1.957549] [I/linux_gpio_adapter] LinuxGpioMatchProbe: find gpio chip(start:128, count:32) [ 1.957668] [I/gpio_manager] GpioManagerAdd: start:128 count:32 added success! [ 1.957715] [I/linux_gpio_adapter] LinuxGpioMatchProbe: add gpio controller(start:128, count:32) succeed! [ 1.957737] [I/linux_gpio_adapter] LinuxGpioMatchProbe: find gpio chip(start:511, count:1) [ 1.957770] [I/gpio_manager] GpioManagerAdd: start:511 count:1 added success! [ 1.957813] [I/linux_gpio_adapter] LinuxGpioMatchProbe: add gpio controller(start:511, count:1) succeed! [ 1.957835] [I/linux_gpio_adapter] LinuxGpioInit: dev service: init done! [ 1.958037] [I/device_node] launch devnode HDF_PLATFORM_GPIO_MANAGER [ 1.958059] [I/gpio_service] GpioServiceBind: enter! [ 1.958083] [I/gpio_service] GpioServiceBind: success! [ 1.958711] [I/osal_cdev] add cdev HDF_PLATFORM_GPIO_MANAGER success [ 1.958711] [ 1.958803] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_EMMC [ 1.958834] [E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_MMC_0, ret = -207 [ 1.958867] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_WATCHDOG [ 1.958892] [E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_WATCHDOG_0, ret = -207 [ 1.959103] [I/device_node] launch devnode HDF_PLATFORM_RTC [ 1.959132] [I/RTC_ADAPTER] HiRtcInit: Hdf dev service:HDF_PLATFORM_RTC init success! [ 1.959654] [I/osal_cdev] add cdev HDF_PLATFORM_RTC success [ 1.959654] [ 1.959810] [I/device_node] launch devnode HDF_PLATFORM_UART_3 [ 1.959836] [I/hdf_uart_adapter] HdfUartBind: entry! [ 1.959859] [I/hdf_uart_adapter] HdfUartInit: entry! [ 1.960288] [I/osal_cdev] add cdev HDF_PLATFORM_UART_3 success [ 1.960288] [ 1.960435] [I/device_node] launch devnode HDF_PLATFORM_UART_1 [ 1.960459] [I/hdf_uart_adapter] HdfUartBind: entry! [ 1.960482] [I/hdf_uart_adapter] HdfUartInit: entry! [ 1.960827] [I/osal_cdev] add cdev HDF_PLATFORM_UART_1 success [ 1.960827] [ 1.960991] [I/device_node] launch devnode HDF_PLATFORM_UART_0 [ 1.961018] [I/hdf_uart_adapter] HdfUartBind: entry! [ 1.961040] [I/hdf_uart_adapter] HdfUartInit: entry! [ 1.961360] [I/osal_cdev] add cdev HDF_PLATFORM_UART_0 success [ 1.961360] [ 1.961590] [I/device_node] launch devnode HDF_PLATFORM_I2C_MANAGER [ 1.961614] [I/i2c_core] I2cManagerBind: enter! [ 1.962325] [I/osal_cdev] add cdev HDF_PLATFORM_I2C_MANAGER success [ 1.962325] [ 1.962714] [I/device_node] launch devnode [ 1.962748] [I/i2c_linux_adapter] LinuxI2cInit: enter! [ 1.962785] [I/i2c_linux_adapter] LinuxI2cProbe: enter! [ 1.962842] [I/i2c_linux_adapter] LinuxI2cProbe: i2c adapter 0 add success! [ 1.962875] [I/i2c_linux_adapter] LinuxI2cProbe: enter! [ 1.962925] [I/i2c_linux_adapter] LinuxI2cProbe: i2c adapter 1 add success! [ 1.962959] [I/i2c_linux_adapter] LinuxI2cC_LSM303 [ 1.984673] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HDF_SENSOR_MAGNETIC_LSM303 not found [ 1.984failed to AddDevice hdf_magnetic_lsm303, ret = -207 [ 1.984759] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamiXIMITY_APDS9960 [ 1.984799] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HDF_SENSOR_PROXIMITY_APDS9960 not found ervice_clnt] failed to AddDevice hdf_proximity_apds9960, ret = -207 [ 1.984881] [I/HDF_LOG_TAG] HdfDriverManagerGetDriviver HDF_SENSOR_ALS_BH1745 [ 1.984921] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HDF_SENSOR_ALS_BH1745 not foundce hdf_als_bh1745, ret = -207 [ 1.985312] [I/device_node] launch devnode hdf_accel_mxc6655xa [ 1.985878] [E/khdf_snsor: i2c[5] read failed [ 1.985925] [E/khdf_sensor_common_driver] DetectSensorDevice: i2c read chip id failed [ 1iver] AccelCreateCfgData: Accel sensor detect device no exist [ 1.986012] [I/device_node] release devnode hdf_accel_mxcnsor_common_driver] DeleteSensorDevice: delete sensor id invalid para [ 1.986090] [E/devmgr_service] devmgr detach devi 1.986138] [E/devhost_service_clnt] failed to AddDevice hdf_accel_mxc6655xa, ret = -204 [ 1.986199] [I/HDF_LOG_TAG] Hmic load driver HDF_SENSOR_TEMPERATURE [ 1.986243] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HDF_SENSOR_TEMPERAT 1.986279] [E/devhost_service_clnt] failed to AddDevice hdf_sensor_temperature, ret = -207 [ 1.986326] [I/HDF_LOG_TAG]GetDriver:try to dynamic load driver HDF_SENSOR_HUMIDITY [ 1.986365] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver H [ 1.986400] [E/devhost_service_clnt] failed to AddDevice hdf_sensor_humidity, ret = -207 [ 1.986509] [I/HDF_LOG_TDriver:try to dynamic load driver HDF_CAMERA_ADAPTER [ 1.986552] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HDF_C [ 1.986591] [E/devhost_service_clnt] failed to AddDevice hdfcamera0, ret = -207 [ 1.986637] [I/HDF_LOG_TAG] HdfDr to dynamic load driver HDF_CAMERA [ 1.986679] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HDF_CAMERA not found service_clnt] failed to AddDevice hdfcamera, ret = -207 [ 1.986801] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dy [ 2.122022] [E/HDF_LOG_TAG] SetTiming: enable = 0 [ 2.165762] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 2.165847] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 2.165883] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 2.272412] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 2.272495] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 2.272535] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 19 time [ 2.272590] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 2.425759] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 2.425849] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 2.425883] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 2.532404] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 2.532484] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 2.532523] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 18 time [ 2.532579] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 2.685743] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 2.685826] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 2.685862] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 2.792407] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 2.792485] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 2.792521] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 17 time [ 2.792576] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 2.945742] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 2.945835] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 2.945873] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 3.052405] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 3.052485] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 3.052522] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 16 time [ 3.052579] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 3.205742] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 3.205827] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 3.205861] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 3.312408] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 3.312489] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 3.312526] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 15 time [ 3.312582] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 3.465776] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 3.465860] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 3.465894] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 3.572451] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 3.572529] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 3.572566] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 14 time [ 3.572623] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 3.725741] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 3.725822] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 3.725857] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 3.832406] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 3.832485] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 3.832522] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 13 time [ 3.832576] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 3.985737] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 3.985818] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 3.985853] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 4.092352] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 4.092432] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 4.092470] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 12 time [ 4.092524] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 4.245745] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 4.245829] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 4.245863] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 4.352451] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 4.352530] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 4.352566] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 11 time [ 4.352620] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 4.425442] vendor storage:20190527 ret = -1 [ 4.505748] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 4.505832] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 4.505865] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 4.612397] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 4.612476] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 4.612512] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 10 time [ 4.612566] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 4.765785] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 4.765866] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 4.765900] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 4.872404] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 4.872483] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 4.872522] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 9 time [ 4.872575] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 5.025739] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 5.025820] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 5.025855] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 5.132467] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 5.132549] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 5.132583] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 8 time [ 5.132638] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 5.285783] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 5.285865] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 5.285898] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 5.392410] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 5.392489] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 5.392525] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 7 time [ 5.392579] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 5.545783] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 5.545862] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 5.545897] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 5.652397] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 5.652479] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 5.652516] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 6 time [ 5.652570] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 5.805741] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 5.805824] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 5.805858] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 5.912407] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 5.912486] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 5.912521] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 5 time [ 5.912575] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 6.065743] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 6.065825] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 6.065859] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 6.172367] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 6.172449] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 6.172486] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 4 time [ 6.172543] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 6.325728] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 6.325810] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 6.325844] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 6.432448] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 6.432528] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 6.432564] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 3 time [ 6.432622] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 6.585741] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 6.585821] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 6.585855] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 6.692395] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 6.692474] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 6.692510] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 2 time [ 6.692564] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 6.845738] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 6.845820] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 6.845855] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 6.952403] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 6.952482] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 6.952520] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 1 time [ 6.952575] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 7.105739] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 7.105820] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 7.105855] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 7.212458] [E/HDF_LOG_TAG] InputI2cRead: i2c read err [ 7.212540] [E/HDF_INPUT_DRV] ChipDetect: read chip version failed [ 7.212576] [I/HDF_LOG_TAG] ChipDriverInit: reset chip 0 time [ 7.212632] [E/HDF_LOG_TAG] SetTiming: enable = 1 [ 7.365742] [E/HDF_LOG_TAG] InputI2cWrite: i2c write err [ 7.365825] [E/HDF_LOG_TAG] SetResetStatus: InputI2cWrite failed, ret = -1 [ 7.365861] [E/HDF_LOG_TAG] SetTiming: SetResetStatus failed [ 7.365916] [I/device_node] release devnode hdf_touch_gt911_service [ 7.365951] [I/HDF_INPUT_DRV] HdfGoodixChipRelease: goodix chip is release [ 7.365993] [E/devmgr_service] devmgr detach device 3000301 not found [ 7.366044] [E/devhost_service_clnt] failed to AddDevice hdf_touch_gt911_service, ret = -204 [ 7.366494] [I/device_node] launch devnode [ 7.366529] [I/HDF_LOG_TAG] RegisterInputDevice: enter [ 7.366563] [I/HDF_LOG_TAG] CreateDeviceNode: prepare to register hdf device [ 7.366631] [I/device_node] launch devnode [ 7.367488] [I/osal_cdev] add cdev hdf_input_event2 success [ 7.367488] [ 7.367566] [I/HDF_LOG_TAG] HidRegisterHdfDevice: svcName is hdf_input_event2, devName = hid-powerkey [ 7.367603] [I/HDF_LOG_TAG] CreateDeviceNode: create node succ, devId is 2 [ 7.368603] [E/HDF_LOG_TAG] HotPlugNotify: send event failed [ 7.368653] [I/HDF_LOG_TAG] RegisterInputDevice: exit succ, devCount is 1 [ 7.369246] [I/device_node] launch devnode hdf_bl [ 7.369284] [I/HDF_DISP] BacklightInit success [ 7.370074] [I/osal_cdev] add cdev hdf_bl success [ 7.370074] [ 7.370419] [I/device_node] launch devnode [ 7.370486] [E/pwm_adapter] HdfPwmOpen: pwm_request pwm1 fail! [ 7.370520] [E/pwm_core] PwmDeviceGet: open fail, ret: -1! [ 7.370551] [E/pwm_if] PwmOpen: PwmDeviceGet fail, ret: -1! [ 7.370582] [E/HDF_DISP] BlPwmDevInit: PwmOpen failed [ 7.370609] [E/HDF_DISP] BlPwmEntryInit: BlPwmDevInit fail [ 7.370642] [I/device_node] release devnode [ 7.370676] [E/devmgr_service] devmgr detach device 2000501 not found [ 7.370720] [E/devhost_service_clnt] failed to AddDevice , ret = -204 [ 7.371039] [I/device_node] launch devnode [ 7.372063] [E/HDF_DISP] PanelEntryInit of_find_compatible_node fail [ 7.372122] [I/device_node] release devnode [ 7.372166] [E/devmgr_service] devmgr detach device 2000404 not found [ 7.372213] [E/devhost_service_clnt] failed to AddDevice , ret = -204 [ 7.372288] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver LCD_ICN9700 [ 7.372332] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver LCD_ICN9700 not found [ 7.372368] [E/devhost_service_clnt] failed to AddDevice , ret = -207 [ 7.372414] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HI351XX_DISP [ 7.372453] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver HI351XX_DISP not found [ 7.372489] [E/devhost_service_clnt] failed to AddDevice , ret = -207 [ 7.372883] [I/device_node] launch devnode hdf_disp [ 7.372916] [E/HDF_DISP] HdfDispEntryInit: panelManager is null! [ 7.372947] [I/device_node] release devnode hdf_disp [ 7.372980] [E/devmgr_service] devmgr detach device 2000201 not found [ 7.373020] [E/devhost_service_clnt] failed to AddDevice hdf_disp, ret = -204 [ 7.373315] [I/device_node] launch devnode [ 7.373349] [E/HDF_DISP] HdfDrmPanelEntryInit manager is null [ 7.373377] [I/device_node] release devnode [ 7.373408] [E/devmgr_service] devmgr detach device 2000101 not found [ 7.373448] [E/devhost_service_clnt] failed to AddDevice , ret = -204 [ 7.373850] [I/device_node] launch devnode hdmi_dma_service_0 [ 7.373956] [I/HDF_AUDIO_KADM] [AudioSocRegisterPlatform][line:60]: Register [hdmi_dma_service_0] success. [ 7.374184] [I/device_node] launch devnode dma_service_0 [ 7.374288] [I/HDF_AUDIO_KADM] [AudioSocRegisterPlatform][line:60]: Register [dma_service_0] success. [ 7.374520] [I/device_node] launch devnode dsp_service_0

[ 7.374643] [I/HDF_AUDIO_KADM] [AudioSocRegisterDai][line:87]: Register [dsp_dai] success. [ 7.374679] [I/HDF_AUDIO_KADM] [AudioRegisterDsp][line:168]: Register [dsp_service_0] success.

[ 7.374921] [I/device_node] launch devnode codec_service_1

[ 7.376702] [I/HDF_AUDIO_KADM] [AudioSocRegisterDai][line:87]: Register [hdmi_codec_dai] success. [ 7.376745] [I/HDF_AUDIO_KADM] [AudioRegisterCodec][line:128]: Register [codec_service_1] success.

[ 7.376992] [I/device_node] launch devnode codec_service_0 [ 7.379181] [I/HDF_AUDIO_KADM] [AudioSocRegisterDai][line:87]: Register [codec_dai] success. [ 7.379228] [I/HDF_AUDIO_KADM] [AudioRegisterCodec][line:128]: Register [codec_service_0] success. [ 7.379462] [I/device_node] launch devnode hdmi_dai_service [ 7.379554] [I/HDF_AUDIO_KADM] [AudioSocRegisterDai][line:87]: Register [hdmi_dai_service] success. [ 7.379759] [I/device_node] launch devnode dai_service [ 7.380627] [I/HDF_AUDIO_KADM] [AudioSocRegisterDai][line:87]: Register [dai_service] success. [ 7.380837] [I/device_node] launch devnode hdf_audio_codec_primary_dev0

[ 7.380933] [I/HDF_AUDIO_KADM] [AudioFillConfigData][line:115]: cardServiceName = hdf_audio_codec_primary_dev0 [ 7.380969] [I/HDF_AUDIO_KADM] [AudioFillConfigData][line:116]: codecName = codec_service_0, codecDaiName = codec_dai [ 7.381003] [I/HDF_AUDIO_KADM] [AudioFillConfigData][line:117]: platformName = dma_service_0, cpuDaiNamei = dai_service [ 7.381035] [I/HDF_AUDIO_KADM] [AudioFillConfigData][line:118]: dspName = dsp_service_0, dspDaiName = dsp_dai [ 7.381073] [I/HDF_AUDIO_KADM] [AudioBindDaiLink][line:324]: PLATFORM [dma_service_0] is registered! [ 7.381107] [I/HDF_AUDIO_KADM] [AudioBindDaiLink][line:327]: CPUDAI [dai_service] is registered! [ 7.381139] [I/HDF_AUDIO_KADM] [AudioBindDaiLink][line:330]: CODEC [codec_service_0] is registered! [ 7.381170] [I/HDF_AUDIO_KADM] [AudioBindDaiLink][line:331]: CODECDAI [codec_dai] is registered! [ 7.381202] [I/HDF_AUDIO_KADM] [AudioBindDaiLink][line:334]: DSP [dsp_service_0] is registered! [ 7.381232] [I/HDF_AUDIO_KADM] [AudioBindDaiLink][line:335]: DSPDAI [dsp_dai] is registered!

[ 7.850832] [I/osal_cdev] add cdev hdf_audio_codec_primary_dev0 success [ 7.850832] [ 7.851338] [I/device_node] launch devnode hdf_audio_control

[ 7.852294] [I/osal_cdev] add cdev hdf_audio_control success [ 7.852294] [ 7.852744] [I/device_node] launch devnode hdf_audio_capture

[ 7.853538] [I/osal_cdev] add cdev hdf_audio_capture success [ 7.853538] [ 7.853938] [I/device_node] launch devnode hdf_audio_render

[ 7.854653] [I/osal_cdev] add cdev hdf_audio_render success [ 7.854653] [ 7.854940] [I/device_node] launch devnode analog_headset_service [ 7.856064] [E/analog_headset_core] [HdfHeadsetInit][line:440]: g_pdataInfo is NULL! [ 7.856111] [I/device_node] release devnode analog_headset_service [ 7.856219] [E/analog_headset_core] [HdfHeadsetExit][line:473]: device or device->priv is NULL. [ 7.856268] [E/devmgr_service] devmgr detach device 8000801 not found [ 7.856314] [E/devhost_service_clnt] failed to AddDevice analog_headset_service, ret = -204 [ 7.856842] [I/device_node] launch devnode hdf_uevent_ut [ 7.857668] [I/osal_cdev] add cdev hdf_uevent_ut success [ 7.857668] [ 7.858044] [I/device_node] launch devnode pm_ut_service [ 7.858079] [I/pm_driver_test] HdfPmDriverBind enter [ 7.858108] [I/pm_driver_test] HdfPmDriverInit enter! [ 7.858162] [I/pm_driver_test] HdfPmDriverInit register power listener, ret = 0 [ 7.859025] [I/osal_cdev] add cdev pm_ut_service success [ 7.859025] [ 7.859415] [I/device_node] launch devnode sample_service [ 7.859468] [I/sample_driver_test] HdfSampleDriverInit::enter! [ 7.859551] [I/sample_driver_test] HdfSampleDriverInit:register power listener, ret = 0 [ 7.860253] [I/osal_cdev] add cdev sample_service success [ 7.860253] [ 7.860626] [I/device_node] launch devnode khdf_ut [ 7.861263] [I/osal_cdev] add cdev khdf_ut success [ 7.861263] [ 7.861590] [I/device_node] launch devnode HDF_PLATFORM_PWM_10 [ 7.861652] [I/pwm_virtual] VirtualPwmProbe: set PwmConfig: number 10, period 999, duty 333, polarity 0, enable 0! [ 7.861886] [I/pwm_virtual] VirtualPwmInit: pwm init success! [ 7.862509] [I/osal_cdev] add cdev HDF_PLATFORM_PWM_10 success [ 7.862509] [ 7.862883] [I/device_node] launch devnode [ 7.863825] [I/khdf_sensor_common_driver] AddSensorDevice: register sensor name[sensor_test] success [ 7.863873] [I/hdf_sensor_test_c] InitSensorDriverTest: init sensor test driver success [ 7.864175] [I/device_node] launch devnode UART_TEST [ 7.864892] [I/osal_cdev] add cdev UART_TEST success [ 7.864892] [ 7.865128] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver PLATFORM_MIPI_DSI_TEST [ 7.865188] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver PLATFORM_MIPI_DSI_TEST not found [ 7.865227] [E/devhost_service_clnt] failed to AddDevice PLATFORM_MIPI_DSI_TEST, ret = -207 [ 7.865269] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver PLATFORM_SDIO_TEST [ 7.865308] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver PLATFORM_SDIO_TEST not found [ 7.865340] [E/devhost_service_clnt] failed to AddDevice SDIO_TEST, ret = -207 [ 7.865378] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver PLATFORM_EMMC_TEST [ 7.865414] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver PLATFORM_EMMC_TEST not found [ 7.865446] [E/devhost_service_clnt] failed to AddDevice EMMC_TEST, ret = -207 [ 7.865705] [I/device_node] launch devnode SPI_TEST [ 7.866012] [I/device_node] launch devnode RTC_TEST [ 7.866701] [I/osal_cdev] add cdev RTC_TEST success [ 7.866701] [ 7.867039] [I/device_node] launch devnode [ 7.867108] [E/i2c_dummy] DummyI2cInit: i2c dummy adapter 15 add success [ 7.867353] [I/device_node] launch devnode I2C_TEST [ 7.868100] [I/osal_cdev] add cdev I2C_TEST success [ 7.868100] [ 7.868486] [I/device_node] launch devnode GPIO_TEST [ 7.868543] [I/HDF_LOG_TAG] GpioTestBind: done! [ 7.869179] [I/osal_cdev] add cdev GPIO_TEST success [ 7.869179] [ 7.869294] [I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver PLATFORM_WATCHDOG_TEST [ 7.869344] [E/HDF_LOG_TAG] HdfDriverManagerGetDriver:driver PLATFORM_WATCHDOG_TEST not found [ 7.869380] [E/devhost_service_clnt] failed to AddDevice WATCHDOG_TEST, ret = -207 [ 7.869631] [I/device_node] launch devnode PWM_TEST [ 7.870277] [I/osal_cdev] add cdev PWM_TEST success [ 7.870277] [ 7.870581] [I/device_node] launch devnode ADC_TEST [ 7.870628] [I/adc_test_driver_c] AdcTestBind: done! [ 7.870659] [I/adc_test_driver_c] AdcTestInit: done! [ 7.871266] [I/osal_cdev] add cdev ADC_TEST success [ 7.871266] [ 7.871410] [I/hdf_power_manager] HdfPmTaskQueueInit HdfTaskQueueCreate success [ 7.871561] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 7.878121] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 7.878684] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 7.878736] cfg80211: failed to load regulatory.db [ 7.879286] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 409; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '10:15:17', on 'Jul 25 2024'. [ 7.880804] Mali: [ 7.880817] Mali device driver loaded [ 7.880886] rkisp rkisp-vir0: clear unready subdev num: 2 [ 7.880922] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.883102] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.883147] rkisp-vir0: update sensor failed [ 7.894681] Freeing unused kernel memory: 1664K [ 7.905482] Run /init as init process [ 7.906604] [I/xpm_kernel]get_dm_verity_partition_dev: get / dev=2:2 success [ 7.906702] [I/xpm_kernel]report_security_info: 1011009110: { "event_type": "dm-verity disable", "timestamp": 1501923610 } [ 7.923952] [pid=1][Init][INFO][init.c:232]Start init first stage. [ 8.015624] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.015799] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName updater [ 8.016191] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName sysdata [ 8.016570] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName sys_prod [ 8.016939] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName odm [ 8.017394] [pid=1][ueventd][INFO][ueventd.c:191]Handle required partitionName system [ 8.018130] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p5->/dev/block/platform/fe310000.sdhci/by-name/system [ 8.018194] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p5->/dev/block/by-name/system [ 8.018717] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.019635] [pid=1][ueventd][INFO][ueventd.c:191]Handle required partitionName boot_linux [ 8.020224] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p3->/dev/block/platform/fe310000.sdhci/by-name/boot_linux [ 8.020279] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p3->/dev/block/by-name/boot_linux [ 8.020739] [pid=1][ueventd][INFO][ueventd.c:191]Handle required partitionName uboot [ 8.021281] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p1->/dev/block/platform/fe310000.sdhci/by-name/uboot [ 8.021333] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p1->/dev/block/by-name/uboot [ 8.021895] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName userdata [ 8.022644] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName chip_prod [ 8.023200] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName syscfg [ 8.023636] [pid=1][ueventd][INFO][ueventd.c:191]Handle required partitionName vendor [ 8.024235] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p6->/dev/block/platform/fe310000.sdhci/by-name/vendor [ 8.024292] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p6->/dev/block/by-name/vendor [ 8.024757] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.025729] [pid=1][ueventd][INFO][ueventd.c:191]Handle required partitionName ramdisk [ 8.026281] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p4->/dev/block/platform/fe310000.sdhci/by-name/ramdisk [ 8.026334] [pid=1][ueventd][INFO][ueventd_device_handler.c:85]symlink /dev/block/mmcblk0p4->/dev/block/by-name/ramdisk [ 8.026757] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName resource [ 8.113243] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.114008] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.114381] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.115124] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.115850] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.116554] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.117252] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.117973] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.118339] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.119124] [pid=1][ueventd][WARNING][ueventd.c:196]Not found device for partitionName (null) [ 8.122727] [pid=1][Init][INFO][init_mount.c:30]Mount required partitions [ 8.122773] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param ohos.boot.bootslots [ 8.122826] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access ohos.boot.bootslots label 0 0 [ 8.122841] [pid=1][BEGET][INFO][fstab_mount.c:330]No valid slot value found from parameter, try to get it from cmdline [ 8.122942] [pid=1][BEGET][INFO][fstab_mount.c:428]boot slots is 2, now adjust partition name according to current slot [ 8.122959] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param ohos.boot.currentslot [ 8.122992] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access ohos.boot.currentslot label 0 0 [ 8.123006] [pid=1][BEGET][INFO][fstab_mount.c:339]No valid slot value found from parameter, try to get it from cmdline [ 8.123083] [pid=1][BEGET][INFO][fstab_mount.c:303]Failed to get currentslot value from cmdline [ 8.123098] [pid=1][BEGET][INFO][fstab_mount.c:344]No valid slot value found from cmdline, try to get it from bootctrl [ 8.123192] [pid=1][BEGET][ERROR][fstab.c:330]Failed to get fstab item from mount point " /bootctrl " [ 8.123207] [pid=1][BEGET][INFO][fstab.c:511]Mount point not found, try to get path by device name. [ 8.123224] [pid=1][BEGET][ERROR][fstab_mount.c:311]Failed to get bootctrl device [ 8.123236] [pid=1][BEGET][ERROR][fstab_mount.c:410]slot value -1 is invalid, set default value ls ls ls ls [ 8.123250] [pid=1][BEGET][INFO][fstab_mount.c:415]partition name with slot suffix: /dev/block/platform/fe310000.sdhci/by-name/system_a [ 13.127196] [pid=1][Init][ERROR][init_utils.c:388]wait for file:/dev/block/platform/fe310000.sdhci/by-name/system_a failed after 5 second. [ 13.127621] [pid=1][BEGET][WARNING][fstab_mount.c:395]Mount /dev/block/platform/fe310000.sdhci/by-name/system_a to /usr failed, err = 2. Ignore failure [ 13.127706] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param ohos.boot.bootslots [ 13.127906] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access ohos.boot.bootslots label 0 0 [ 13.127976] [pid=1][BEGET][INFO][fstab_mount.c:330]No valid slot value found from parameter, try to get it from cmdline [ 13.128651] [pid=1][BEGET][INFO][fstab_mount.c:428]boot slots is 2, now adjust partition name according to current slot [ 13.128740] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param ohos.boot.currentslot [ 13.128908] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access ohos.boot.currentslot label 0 0 [ 13.128976] [pid=1][BEGET][INFO][fstab_mount.c:339]No valid slot value found from parameter, try to get it from cmdline [ 13.129353] [pid=1][BEGET][INFO][fstab_mount.c:303]Failed to get currentslot value from cmdline [ 13.129427] [pid=1][BEGET][INFO][fstab_mount.c:344]No valid slot value found from cmdline, try to get it from bootctrl [ 13.129900] [pid=1][BEGET][ERROR][fstab.c:330]Failed to get fstab item from mount point " /bootctrl " [ 13.129971] [pid=1][BEGET][INFO][fstab.c:511]Mount point not found, try to get path by device name. [ 13.130057] [pid=1][BEGET][ERROR][fstab_mount.c:311]Failed to get bootctrl device [ 13.130113] [pid=1][BEGET][ERROR][fstab_mount.c:410]slot value -1 is invalid, set default value [ 13.130179] [pid=1][BEGET][INFO][fstab_mount.c:415]partition name with slot suffix: /dev/block/platform/fe310000.sdhci/by-name/vendor_a [ 18.134142] [pid=1][Init][ERROR][init_utils.c:388]wait for file:/dev/block/platform/fe310000.sdhci/by-name/vendor_a failed after 5 second. [ 18.134614] [pid=1][BEGET][WARNING][fstab_mount.c:395]Mount /dev/block/platform/fe310000.sdhci/by-name/vendor_a to /vendor failed, err = 2. Ignore failure [ 18.134698] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param ohos.boot.bootslots [ 18.134887] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access ohos.boot.bootslots label 0 0 [ 18.134958] [pid=1][BEGET][INFO][fstab_mount.c:330]No valid slot value found from parameter, try to get it from cmdline [ 18.135629] [pid=1][BEGET][INFO][fstab_mount.c:428]boot slots is 2, now adjust partition name according to current slot [ 18.135739] [pid=1][BEGET][ERROR][fstab_mount.c:361]Unsupported file system " none " [ 18.136135] [pid=1][Init][INFO][init.c:211]Start init second stage. [ 18.136453] [pid=1][Init][WARNING][switch_root.c:162]Try to switch root in same device, skip switching root [ 18.153484] [pid=1][Init][INFO][init.c:90]Init fd holder socket done [ 18.155282] [pid=1][BEGET][ERROR][fstab.c:330]Failed to get fstab item from mount point " /misc " [ 18.155406] [pid=1][BEGET][INFO][fstab.c:511]Mount point not found, try to get path by device name. [ 18.155789] [pid=1][BEGET][ERROR][reboot_misc.c:80]Failed to get misc info [ 18.155861] [pid=1][Init][INFO][init_group_manager.c:201]boot start device.boot.group [ 18.156034] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param const.cust.config_dir_layer [ 18.156214] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access const.cust.config_dir_layer label 0 0 [ 18.156289] [pid=1][PARAM][ERROR][param_include.h:75]Invalid current param const.cust.follow_x_rules [ 18.156440] [pid=1][PARAM][ERROR][param_manager.c:652]Forbid to access const.cust.follow_x_rules label 0 0 [ 18.156739] [pid=1][Init][INFO][init.c:313]Executing hook [0:0] cost [796]us, return 0. [ 18.156839] [pid=1][Init][INFO][init.c:313]Executing hook [0:0] cost [23]us, return 0. [ 18.157257] [pid=1][Init][INFO][init.c:313]Executing hook [0:0] cost [336]us, return 0. [ 18.157376] [pid=1][Init][INFO][init.c:313]Executing hook [0:0] cost [38]us, return 0. [ 18.157444] [pid=1][PLUGIN][INFO][selinux_static.c:23]Install selinuxadp. [ 18.157650] [pid=1][BEGET][ERROR][modulemgr.c:120]Failed to get real path [ 18.157714] [pid=1][BEGET][ERROR][modulemgr.c:171]Failed to install module selinuxadp [ 18.157786] [pid=1][Init][INFO][init.c:313]Executing hook [0:0] cost [338]us, return 0. [ 18.157867] [pid=1][PARAM][INFO][param_service.c:371]InitParamService pipe: /dev/unix/socket/paramservice. [ 18.158205] [pid=1][PARAM][INFO][param_base.c:187]CloseParamWorkSpace 1 [ 18.158340] [pid=1][PARAM][ERROR][param_base.c:352]Invalid workSpace for musl.log.enable [ 18.158488] [pid=1][PARAM][ERROR][param_base.c:582]Forbid to access parameter musl.log.enable [ 18.158556] [pid=1][PARAM][ERROR][param_base.c:352]Invalid workSpace for musl.ld.debug.dlclose [ 18.158614] [pid=1][PARAM][ERROR][param_base.c:582]Forbid to access parameter musl.ld.debug.dlclose [ 18.158679] [pid=1][PARAM][ERROR][param_base.c:352]Invalid workSpace for debug.hitrace.tags.enableflags [ 18.158736] [pid=1][PARAM][ERROR][param_base.c:582]Forbid to access parameter debug.hitrace.tags.enableflags [ 18.159170] [pid=1][PARAM][ERROR][param_selinux.c:43]Failed to dlsym selinuxHandle, Error loading shared library /system/lib/libparaperm_checker.z.so: No such [ 18.159280] [pid=1][PARAM][INFO][param_base.c:260]AddWorkSpace u:object_r:default_param:s0 index 1 spaceSize: 10485760 onlyRead false [ 18.159663] [pid=1][PARAM][INFO][param_base.c:260]AddWorkSpace param_sec_dac index 0 spaceSize: 20480 onlyRead false [ 18.160486] [pid=1][Init][INFO][init_group_manager.c:68]Parse group config /system/etc/device.boot.group.cfg [ 18.160634] [pid=1][Init][ERROR][init_utils.c:192]Failed to read file /system/etc/device.boot.group.cfg errno:2 [ 18.160701] [pid=1][Init][ERROR][init_group_manager.c:70]Failed to read file content /system/etc/device.boot.group.cfg [ 18.160759] [pid=1][Init][INFO][init.c:410]boot init finish. [ 18.160875] [pid=1][LoopEvent][INFO][le_signal.c:75]LE_AddSignal 17 0 [ 18.161006] [pid=1][LoopEvent][INFO][le_signal.c:75]LE_AddSignal 15 1 [ 18.161189] [pid=1][PARAM][ERROR][param_server.c:263]Failed to open file '/sys_prod/etc/param/ohos.para.size' error:2 [ 18.161340] [pid=1][PARAM][ERROR][param_server.c:263]Failed to open file '/etc/param/ohos.para.size' error:2 [ 18.161419] [pid=1][PARAM][INFO][param_base.c:260]AddWorkSpace u:object_r:default_param:s0 index 1 spaceSize: 10485760 onlyRead false [ 18.162292] [pid=1][PARAM][ERROR][param_server.c:200]Generate default sn now ... [ 18.162766] [pid=1][PARAM][INFO][param_server.c:319]load parameters from build [ 18.162870] [pid=1][PARAM][INFO][param_server.c:305]Load default parameters from /system/etc/param/ohos_const. [ 18.162994] [pid=1][Init][ERROR][init_utils.c:525]Read dir :/system/etc/param/ohos_const failed.2 [ 18.163114] [pid=1][PARAM][ERROR][param_dac.c:183]Read dir :/system/etc/param/ohos_const failed.2 [ 18.163370] [pid=1][Init][INFO][init.c:313]Executing hook [30:0] cost [21]us, return 0. [ 18.163422] [pid=1][PLUGIN][INFO][udid_static.c:21]Begin install udidmodule. [ 18.163561] [pid=1][BEGET][ERROR][modulemgr.c:120]Failed to get real path [ 18.163606] [pid=1][BEGET][ERROR][modulemgr.c:171]Failed to install module udidmodule [ 18.163648] [pid=1][PLUGIN][INFO][udid_static.c:24]Begin uninstall udidmodule. [ 18.163687] [pid=1][BEGET][ERROR][modulemgr.c:280]Can not find module udidmodule [ 18.163724] [pid=1][PLUGIN][INFO][udid_static.c:27]Uninstall udidmodule finished. [ 18.163765] [pid=1][Init][INFO][init.c:313]Executing hook [30:0] cost [345]us, return 0. [ 18.163814] [pid=1][Init][INFO][init_config.c:108]ohos.boot.mode [ 18.163933] [pid=1][Init][ERROR][init_utils.c:137]Unexpected config file " /etc/init.cfg ", check if it exist. if exist, check file size [ 18.163978] [pid=1][Init][ERROR][init_config.c:56]Failed to read file content /etc/init.cfg [ 18.164186] [pid=1][Init][INFO][init.c:429]boot parse config file done. [ 18.164248] [pid=1][PLUGIN][INFO][seccomp_policy_static.c:48]seccomp enabled. [ 18.164293] [pid=1][Init][INFO][init.c:313]Executing hook [50:0] cost [54]us, return 0. [ 18.164444] [pid=1][Init][INFO][init.c:273]boot job pre-init start. [ 18.164502] [pid=1][Init][INFO][init.c:278]boot job pre-init finish diff 66 us. [ 18.164593] [pid=1][Init][INFO][init.c:273]boot job init start. [ 18.164647] [pid=1][Init][INFO][init.c:278]boot job init finish diff 58 us. [ 18.164740] [pid=1][Init][INFO][init.c:273]boot job post-init start. [ 18.164793] [pid=1][Init][INFO][init.c:278]boot job post-init finish diff 60 us. [ 38.878752] vcc3v3_lcd0_n: disabling [ 38.878874] vcc3v3_lcd1_n: disabling [ 70.455234] random: crng init done

您尚未登录,无法参与评论,登录后可以:
参与开源共建问题交流
认同或收藏高质量问答
获取积分成为开源共建先驱

精彩评论1

润开鸿_闻飞

沙发 发表于 2024-9-11 19:33:54
串口的Flow control设置成None试试

Copyright   ©2023  OpenHarmony开发者论坛  京ICP备2020036654号-3 |技术支持 Discuz!

返回顶部