```
DDR 9fffbe1e78 cym 24/02/04-10:09:20,fwver: v1.16
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0xff
CH0 RX Vref:27.9%, TX Vref:24.8%,24.8%
CH1 RX Vref:27.9%, TX Vref:23.8%,23.8%
CH2 RX Vref:29.7%, TX Vref:24.8%,23.8%
CH3 RX Vref:29.3%, TX Vref:21.8%,23.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x2000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(6dbe36e3e6...) + OK
## Checking uboot 0x00200000 ... sha256(beed0472cc...) + OK
## Checking fdt 0x0032a1d0 ... sha256(195cf07805...) + OK
## Checking atf-2 0xff100000 ... sha256(40e9180d15...) + OK
## Checking atf-3 0x000f0000 ... sha256(d189664c33...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 478.704/648.4 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-754-g371ede2b2:cym, fwver:
NOTICE: BL31: Built : 19:36:27, Apr 22 2024
INFO: spec: 0x1
INFO: code: 0x88
INFO: ext 32k is valid
INFO: ddr: stride-en 4CH
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO: l3 cache partition cfg-0
INFO: system boots from cpu-hwid-0
INFO: disable memory repair
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09 (Nov 06 2024 - 20:43:53 +0800)
Model: Orange Pi 5B
PreSerial: 2, raw, 0xfeb50000
DRAM: mem size is less then 4GB
mem size is less then 4GB
mem size is less then 4GB
8 GiB
Sysmem: init
Relocation Offset: edb4d000
Relocation fdt: eb9f7ea8 - eb9fecd8
CR: M/C/I
mem size is less then 4GB
mem size is less then 4GB
mem size is less then 4GB
Using default environment
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: recovery (misc)
FIT: No recovery partition
168843 bytes read in 6 ms (26.8 MiB/s)
DTB(Distro): /extlinux/toybrick.dtb
Pre-reloc: vcc5v0_sys
Pre-reloc: vcc_mipicsi1
Pre-reloc: wifi_disable
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
get vp0 plane mask:0x5, primary id:0, cursor_plane:2, from dts
get vp1 plane mask:0xa, primary id:1, cursor_plane:3, from dts
get vp2 plane mask:0x140, primary id:6, cursor_plane:8, from dts
get vp3 plane mask:0x280, primary id:7, cursor_plane:9, from dts
Model: RK3588
if_type: 6
devnum: 0
part_type: 5
target: 0
lun: 0
hwpart: 0
type: 0
removable: 1
op_flag: 0
lba: 488554496
blksz: 512
log2blksz: 9
vendor: Man 0000d6 Snr b4ae53d1
product: A3A564
revision: 1.1
sig_type: 2
cnt : 1
ARCH_DMA_MINALIGN: 64
Cannot find partition 'bootctrl'
read A/B slot failed
Found DTB in resource part
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 0
vp1 have layer nr:2[1 3 ], primary plane: 1
vp2 have layer nr:2[6 8 ], primary plane: 6
vp3 have layer nr:2[7 9 ], primary plane: 7
Monitor has basic audio support
color_format:1
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x2025
hdmi@fde80000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 2025
VOP update mode to: 1920x1080p60, type: HDMI0 for VP0
dclk:148500,if_pixclk_div;2,if_dclk_div:4
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
VP0 set crtc_clock to 1485KHz
VOP VP0 enable Cluster0[800x480->800x480@560x300] fmt[1] addr[0xee01a000]
CEA mode used vic=16
mtmdsclock:148500000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
bus_width:0x16a8c8,bit_rate:1485000
hdptx phy lane locked!
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 24000 KHz
b1pll 24000 KHz
lpll 24000 KHz
v0pll 24000 KHz
aupll 786431 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 850000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 594000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "recovery"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
android_image_load_by_partname: Can't find part: recovery
Android image load failed
Android boot failed, error -1.
## Booting FIT Image FIT: No recovery partition
FIT: No fit blob
FIT: No FIT image
Unknown command 'bootrkp' - try 'help'
MMC: no card present
mmc_init: -123, time 0
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:4...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
79 bytes read in 6 ms (12.7 KiB/s)
1: rockchip-kernel-5.10
if_type: 6
devnum: 0
part_type: 5
target: 0
lun: 0
hwpart: 0
type: 0
removable: 1
op_flag: 0
lba: 488554496
blksz: 512
log2blksz: 9
vendor: Man 0000d6 Snr b4ae53d1
product: A3A564
revision: 1.1
sig_type: 2
cnt : 1
ARCH_DMA_MINALIGN: 64
Cannot find partition 'bootctrl'
read A/B slot failed
Get a/b slot failed. assume device do not support A/B partition
find partition ' ramdisk '
Load from partition ' ramdisk ' to address 0xa200000, count: 8192 block(s)
Read from partition ' ramdisk ' done, total block(s) 8192
Openharmony ramdisk_addr_r = 0x0a200000:0x400000
find partition ' boot_linux '
MMC: no card present
mmc_init: -123, time 0
Cannot find dev_desc in mmc1
set defaultSlect 0
Load from partition ' boot_linux ' to address 0x400000, count: 196608 block(s)
Read from partition ' boot_linux ' done, total block(s) 196608
Retrieving file: /extlinux/Image
34629640 bytes read in 194 ms (170.2 MiB/s)
Retrieving file: /extlinux/toybrick.dtb
168843 bytes read in 6 ms (26.8 MiB/s)
Fdt Ramdisk skip relocation
## Flattened Device Tree blob at 0x0a100000
Booting using the fdt blob at 0x0a100000
'reserved-memory' cma: addr=10000000 size=10000000
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 000000000a100000, end 000000000a12c38a
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000)
Total: 1439.961 ms